Engineers develop new control electronics for quantum computers that improve performance, cut costs

Quantum computing experiments now have a new control and readout electronics option that will significantly improve performance while replacing cumbersome and expensive systems.

Self-assembled logic circuits created from proteins

In a proof-of-concept study, researchers have created self-assembled, protein-based circuits that can perform simple logic functions. The work demonstrates that it is possible to create stable digital circuits that take advantage of an electron's properties at quantum scales.

How to Make a Dual 5V Power Supply From USB

In this guide, I’ll show you how to build a dual +5V -5V power supply from a standard USB outlet.

Dual power supplies with a negative output taken from the positive output can be a little tricky. It’s not a matter of difficulty, but about the low availability of support for easier ways to do this kind of power supply.

So I’ll show you one of the easiest ways to make a dual power supply (also known as bipolar power supply) using a simple USB connection.

It is fair to mention, that this will be for low-power projects since the IC used for this is not capable of outputting much power.

Dual 5V Power Supply Circuit

The Dual Power Supply Schematic

Components Needed

• ICL7660
• USB connector (Such as this from Digikey)
• 2 x 10 µF Capacitor
• Perfboard or stripboard
• Cables

These are standard components you can find at most electronics shops. For the USB connector, it can be a good idea to buy a breakout board. Those are much easier to solder.

How It Works

The design is very simple. It’s based around the ICL766, which is a switched converter chip that only needs two capacitors; one placed between two pins of the chip and another one placed in the negative output of the IC.

The positive 5V will come directly from the micro USB (or USB) connection, from which you’ll only use the power cables since no data is going to be used. Note that the output capacitor is connected with the positive to GND and the negative to the output (since GND is the most positive of the two).

Building the Circuit

This circuit can be tested through a breadboard without any issue. But to have a practical circuit to use for future projects, it’s better to solder it to a perfboard or stripboard. This can also improve the performance of the output.

Step 1: Design a Diagram

The first thing you want to do is design a diagram for how to connect everything on the stripboard. Use the schematic above to see all the connections. Here’s the board I designed:

If you use a different USB connector or type of board you will probably have to do some changes to the above design to make it fit.

It’s smart to take some time and do this step properly before you start soldering. Then you’ll avoid the hassle of desoldering and fixing errors later on.

Step 2: Place and Solder the Components

Place and solder each component in the places that you planned in the previous step:

Step 3: Make the Connections

Next, make all the missing connections with solder blobs between pads (like I did below) or use wires. It’s a good habit to check the continuity with any adjacent points to avoid any possible unwanted connection.

Step 4: Test the Board

The board is ready to be used with 5V, -5V, and GND outputs from top to bottom. Use a multimeter to check that you’re getting these voltages.

The Result

For this prototype, the performance was expected to be a bit worse than what the datasheet showed. To check, I did a series of tests using different resistors as loads for the negative output of the IC. The results are shown below:

Resistance (Ohm)	Voltage (V)	Current (mA)	Voltage Conversion Efficiency
1000000	-5.04	0.004	1
100000	-5.04	0.033	1
10000	-5.02	0.5	0.996031746
5100	-4.98	0.966	0.9880952381
2000	-4.85	2.42	0.9623015873
1660	-4.81	2.9	0.9543650794
1440	-4.78	3.31	0.9484126984
1220	-4.73	3.87	0.9384920635
1000	-4.66	4.64	0.9246031746
880	-4.62	5.2	0.9166666667
660	-4.49	6.76	0.8908730159
440	-4.24	9.51	0.8412698413
330	-3.97	11.73	0.7876984127
220	-3.6	15.69	0.7142857143
100	-2.58	25.6	0.5119047619
80	-2.56	28	0.5079365079
60	-2.1	30.8	0.4166666667
40	-1.49	35.3	0.2956349206
20	-0.93	39.9	0.1845238095
10	-0.39	40.4	0.07738095238

The results for this prototype show that the voltage conversion efficiency is relatively high until the IC starts supplying around 10mA.

So as you try to pull out more current, your negative output will move towards 0V, while the positive output stays at 5V.

But this is not an issue for most op-amp uses, since this will only limit the maximum negative range of the output of the op-amp. So you can still use a diminished negative voltage as long you don’t need it so low.

If you plan on building this, I recommend you test your IC design with different resistors before putting it to use, so that you know how much current you can get from it while still maintaining the negative voltage you need.

Copyright Build Electronic Circuits

Electronic skin anticipates and perceives touch from different directions for the first time

Scientists have developed a new approach for miniaturization of soft ultra-compact and highly integrated sensor units for directional tactile sensitivity in e-skin systems.

Researchers unveil a highly efficient means to reverse magnetization with spin currents

Researchers have established a low-cost method of magnetization reversal on perpendicularly magnetized ferromagnets. Not needing an external magnetic field, the method brings reverse magnetization closer to commercial viability.

Uncovering the secret of ternary polymer solar cell success

A research team has used electron spin resonance spectroscopy to investigate a polymer solar cell while in operation. Molecular level comparison of the PTzBT/PC61BM system with and without added ITIC allowed them to establish the mechanism for the improvements in stability and power conversion efficiency observed when ITIC is added. It is hoped that this insight will contribute to the commercial realization of cost-effective flexible polymer solar cells.

Almost ready for prime time: Deep UV photodetectors head to real-world testing

Researchers are asking why, after decades of development and promising results, ultrawide bandgap photodetectors with deep UV capabilities haven't enjoyed widespread adoption, and are taking stock of advancements and challenges in the field. Unlike their silicon-based counterparts, UWBG photodetectors made from aluminum gallium nitride and gallium (III) oxide are more efficient, can tailor cutoff wavelengths, and do not need optical filters to reject visible or infrared wavelengths for solar-blind applications.

Researchers take step toward developing 'electric eye'

Using nanotechnology, scientists have created a newly designed neuromorphic electronic device that endows microrobotics with colorful vision. The newly designed artificial vision device could have far-reaching applications for the fields of medicine, artificial intelligence, and microrobotics.

How to print a robot from scratch: Combining liquids, solids could lead to faster, more flexible 3D creations

Engineers have developed a new way to 3D-print liquid and solid materials together, potentially leading to more dynamic and useful products -- from robots to wearable electronic devices.

Graphene-hBN breakthrough to spur new LEDs, quantum computing

In a discovery that could speed research into next-generation electronics and LED devices, a research team has developed a reliable, scalable method for growing single layers of hexagonal boron nitride on graphene.

New polymer materials make fabricating optical interconnects easier

Researchers have developed new polymer materials that are ideal for making the optical links necessary to connect chip-based photonic components with board-level circuits or optical fibers. These materials can be used to easily create interconnects between photonic chips and optical printed circuit boards, the light-based equivalent of electronic printed circuit boards.

Real-time ultrafast humidity sensing optical sensor

A research team develops a real-time humidity sensing optical sensor. The response time of the new sensor is 10,000 times faster than the conventional sensors and can be mass-produced at low cost.

Scientists find 'knob' to control magnetic behavior in quantum material

Magnetism, one of the oldest technologies known to humans, is at the forefront of new-age materials that could enable next-generation lossless electronics and quantum computers. Researchers have discovered a new 'knob' to control the magnetic behavior of one promising quantum material, and the findings could pave the way toward novel, efficient and ultra-fast devices.

On the edge

When looking at images of the magnetism generated by nano-magnets, researchers revealed the phenomenon of 'edge magnetism': the magnetic material only retained magnetism on its edge -- in fact only within 10 nanometers of the edge.

Investigating newly synthesized thallium compounds for optoelectronic devices

The burgeoning field of optoelectronic devices is driving the development of new alkali metal-based chalcogenides with qualities that have to be robustly investigated.

Making a ‘sandwich’ out of magnets and topological insulators, potential for lossless electronics

A research team has discovered that sandwiching a topological insulator between two 2D ferromagnetic insulators provides a quantum avenue towards ultra-low energy future electronics, or topological photovoltaics.