Wearables take 'logical' step toward onboard control

Engineers design fluidic logic into garments to help people with functional limitations perform tasks without electronic assistance.

Quantum heat pump: A new measuring tool for physicists

Physicists have built a quantum scale heat pump made from particles of light. This device brings scientists closer to the quantum limit of measuring radio frequency signals, useful in for example the hunt for dark matter.

Baseball Game with 5-Run Display

If you are into baseball and would like a challenging ‘real-playing action’ baseball game, typically to exhibit your pitching skills, then you might like to construct this one. It is designed around four easily available and inexpensive digital ICs in the 4000 CMOS series along with some passive components.

This circuit was sent to us by a guest contributor – thanks a lot Johnny!

Parts List

• IC1: CD4093 – Schmitt-triggered NAND gates
• IC2 & IC5: CD4017 – Decade Counter
• IC3: CD4043 – RS Latch
• IC4: CD4015 – Shift registers
• D1-D8: 1N915 Diodes
• L1-L8: Light-Emitting Diodes
• Q1-Q4: NPN transistors (2N2222A)
• R1, R3, R4, R6: Resistor 47 kΩ
• R2: Resistor 470 kΩ
• R5: Resistor 100 Ω
• R7: Resistor 470 Ω
• C1: Resistor 1µF

How to Build the Display

The baseball diamond display for this game can be built by anyone with some artistic talent, or you could have it done in a print shop.

It should have the four bases and the pitcher’s mound format. A typical size for the game display is a 3′ x 3′ display size.

The base-hit targets are simply normally open switches placed close together in a North-South-East-West circular format at the pitcher’s mound location. Keep them apart about 4″ so that the pitched ball does not hit two targets at a time. The switches can have identified hits with acrylic covers over them.

The LEDs are placed at the four base locations on the baseball diamond display to light them up indicating men on base and the runs scored LEDs can be placed across the bottom of the display or wherever the builder chooses.

Here are a couple of photos of some example displays for similar games (but not this exact circuit):

How It Works

If you look at the schematic, you can see that the ‘base hits’ are input to each of the associated four ‘flip-flop’ segments of 4043 (IC1). They are interpreted by the 4017 1-of-10 output counter (IC2) as the ‘base hits’ are generated in pulses by the pulse generator 4093 (IC1). This pulse generator is created by using one segment of four 2-input Schmitt triggered NAND gates, wired as a feedback oscillator to pulse at a rate determined by the C1/R2 values. It’s directly wired to both clock inputs of (IC4), a 4015 two-segment shift register, on Pins 1-9.

On each hit input, a ‘man’ is indicated on the associated base via the outputs displayed on the L1-L3 LEDs wired in series on both IC4a-b segments. As men are placed on and advanced across the bases, according to the base hits made, they will cross the home plate and indicate a ‘run scored’ on another 4017 counter (IC5). The game has a five-run limit on this circuit layout, but more runs can be displayed by adding more output LEDs to the higher-numbered output pins.

To ‘reset’ for a new game press the RST1 switch, clearing both the men on base and any runs scored.

For those that aren’t familiar with digital logic ICs and their design functions, we’ll go through what’s going on in detail below.

How a ‘double hit’ is made

As soon as a ‘single hit’ is registered to a flip-flop segment on IC3, its associated output pin goes to a high state. Let’s assume that a single input is hit. Output Pin 2 of IC3a goes high, passes through Diode D4, and enables the clock generator IC1a at Pin 1. This causes the pulse generator to start pulsing, from its normally-off high output state on Pin 3. It will provide pulses to the IC2 clock input at Pin 14 and both clock input Pins 1&9 of IC4.

IC2 will now start counting until output Pin 4 goes high. This happens after a count of two clock inputs from the clock generator that also provided those two output pulses to IC4 clock inputs as well.

Notice that IC2, when at a reset condition, has its output Pin 3 at a high state and it is wired directly to the ‘serial input’ Pin 7 of IC4a. This input must be at a high state to provide a high output on Pin 5. It will only be high until the pulse generator advances IC2 outputs and then it goes low for the continued input pulsing to IC2. This is necessary because you only want to indicate one man going to 1st base and none after that while pulsing continues. The only time input Pin 7 is high is when Pin 3 on IC2 is in a ‘reset’ condition, but it immediately goes low as the input count advances in accordance with the hit made at that time.

Notice that each base hit has two associated counts; single with 2 counts, double with 4 counts, triple with 6 counts, and a home run with 8 counts. This is necessary so that the runs scored appear as ‘low-to-high’ transitions into the clock input (pin 14) of the IC5 counter.

With that in mind notice that when IC2 has counted two pulses, representing a single hit, Pin 4 of IC2 is wired directly to the ‘reset’ Pin 3 of IC3a. This action only allows for a man to appear on 1st base with two input pulses and then, as IC3a is reset, its output Pin 2 goes to a low state, disabling the pulse generator with Pin 1 of IC1a going low.

Also notice that the output pins of each IC3 are also wired to the anodes of Diodes 5-8, which when at high inputs, are passed through and inverted to a low disabling ‘reset’ state on IC2 at Pin 15. As soon as any output pin on IC3 goes low, after a hit input state, IC1b is returned to output a high to reset IC2 counter to be enabled to receive another hit input.

With a single hit made, as indicated by L1 being lit, let’s assume now that a ‘double’ is the next hit input. Using the same logic as with the single input above the ‘man’ on 1st is now advanced to 3rd base and a man advancing from 1st base to 2nd base at the same time with a final display of ‘men’ on 2nd and 3rd base. Further hits to advance those men to ‘home’ will indicate runs scored on IC5.

Potential Modifications

If you want to have larger light displays then use appropriate-sized transistors to turn on larger bulbs, etc. The output pins on IC5 are not shown with transistors but would require them as well.

How you construct the game is up to you but be assured that the game-play logic is sound with this design. You might want to wire output Pin 3 directly to the input Pins 8-9 and/or Pins 12-23 of IC1 and use their outputs to sound a buzzer or other sound device. A transistor wired to the outputs would be in line with good design as well.

Copyright Build Electronic Circuits

Silicon image sensor that computes

Researchers have developed the first in-sensor processor that could be integrated into commercial silicon imaging sensor chips -- known as complementary metal-oxide-semiconductor (CMOS) image sensors -- that are used in nearly all commercial devices that need capture visual information, including smartphones.

Small molecules, giant (surface) potential

In a molecular feat akin to getting pedestrians in a scramble crosswalk to spontaneously start walking in step, researchers have created a series of molecules that tend to face the same direction to form a 'giant surface potential' when evaporated onto a surface. The resulting electric fields at the surface can help improve the efficiency of organic light-emitting diodes and open new routes for converting vibrations into electricity with organic materials.

Researchers engineer novel material capable of 'thinking'

Someone taps your shoulder. The organized touch receptors in your skin send a message to your brain, which processes the information and directs you to look left, in the direction of the tap. Now, researchers have harnessed this processing of mechanical information and integrated it into engineered materials that 'think'.

Researchers discover a material that can learn like the brain

Researchers have discovered that vanadium dioxide, a compound used in electronics, is capable of 'remembering' the entire history of previous external stimuli. This is the first material to be identified as possessing this property, although there could be others.

Swarms of microrobots could be solution to unblocking medical devices in body

Swarms of microrobots injected into the human body could unblock internal medical devices and avoid the need for further surgery, according to new research.

A breakthrough in magnetic materials research could lead to novel ways to manipulate electron flow with much less energy loss

Newly discovered magnetic interactions in the Kagome layered topological magnet TbMn6Sn6 could be the key to customizing how electrons flow through these materials. Scientists have conducted an in-depth investigation of TbMn6Sn6 to better understand the material and its magnetic characteristics.

Engineers fabricate a chip-free, wireless electronic 'skin'

Engineers fabricated a chip-free, wireless electronic 'skin.' The device senses and wirelessly transmits signals related to pulse, sweat, and ultraviolet exposure, without bulky chips or batteries.

Researchers design new inks for 3D-printable wearable bioelectronics

A team of researchers has developed a new class of biomaterial inks that mimic native characteristics of highly conductive human tissue, much like skin, which are essential for the ink to be used in 3D printing.

Researchers invent self-charging, ultra-thin device that generates electricity from air moisture

Researchers have developed a new moisture-driven electricity generation device made of a thin layer of fabric, sea salt, carbon ink, and a special water-absorbing gel. The device works by keeping one end of the fabric dry, while the other end is perpetually wet. The difference in moisture content of the wet and dry regions of the carbon-coated fabric creates an electric current. This rechargeable fabric-like battery can produce electricity for more than 150 hours and provides higher electrical output than a conventional AA battery, potentially powering everyday electronics.

Ultra-thin but tough implantable material could treat spinal cord injury and Parkinson's disease

Flexible implanted electronics are a step closer toward clinical applications thanks to a recent breakthrough technology. The work uses silicon carbide technology as a new platform for long-term electronic biotissue interfaces.

Combining techniques to create more environmentally friendly, heat resistant, and transparent plastics

Researchers in Japan have developed a new technique for creating polymers which is expected to lead to the development of plastics that are more environmentally friendly, heat resistant, and transparent.

Augmented reality could be the future of paper books, according to new research

Augmented reality might allow printed books to make a comeback against the e-book trend, according to researchers.

The bacteria powering a truly green revolution in personal electronics

Researchers recently announced that they have figured out how to engineer a biofilm that harvests the energy in evaporation and converts it to electricity. This biofilm has the potential to revolutionize the world of wearable electronics, powering everything from personal medical sensors to personal electronics.